Arbeiten an der Elektronischen Parkbremse (EPB)

Aus VCDS Wiki
Wechseln zu: Navigation, Suche

In diesem Tutorial wird erläutert die Grundsätze, die bei arbeiten an der Elektronischen Parkbremse (EPB) zu beachten sind. Die Elektronischen Parkbremse (EPB) wir in VW/Audi/Skoda/Seat verbaut. Die Elektronischen Parkbremse (EPB) ist entweder über die Adresse 53 - Parkbremse] oder bei neueren Fahrzeugen über die Adresse 03 - Bremselektronik erreichbar. Die Details werden im Abschnitt des jeweiligen Fahrzeug erläutert.

Audi

Audi A3/S3 (8V/FF) (MQB platform ABS)

Grundeinstellung
Achtung!
Die Grundeinstellung darf nicht im ausgebauten Zustand erfolgen!
Opening, closing, function tests, and otherwise cycling the Electronic Parking brakes should only be done with the pads and calipers properly installed on the rotors. Please follow the procedures EXACTLY. There's a reason for every step. If you skip any prerequisites or other steps here, you are likely to experience "issues" for which no documented resolutions exist, in which case we will not be able to help you resolve them. It is strongly recommended to run a full Auto-Scan first thing to check for any preexisting faults! There have been several reports of repair shops damaging the Electronic Parking Brake System when trying to do rear brakes, but not telling the customer and then sending the car out the door. Open Rear Parking Brake Prerequisites: Connect a battery charger as per repair manual. Cycle the Parking Brake ON, then OFF first. [Select] [03 - ABS Brakes] [Basic Settings - 04] Select Start lining change mode [Go!] to activate the Basic Setting. The brake calipers will then open, allowing the pads to be changed. You should hear the rear caliper motors operating. Wait 30 seconds after it says Not Running or the noises have stopped before clicking [Stop] [Done, Go Back] [Close Controller, Go Back - 06]

Turn ignition off and leave battery charger connected. The caliper pistons do not move back into the caliper, they must be pushed in using a hand tool. Fault code 721152 - Brake pad replacement mode active will be stored, this is normal.

Close Rear Parking Brake Prerequisites: Connect a battery charger as per repair manual. [Select] [03 - ABS Brakes] [Basic Settings - 04] Select End lining change mode [Go!] to activate the Basic Setting. The brake calipers will then close. Wait 30 seconds after it says Not Running or the noises have stopped before clicking [Stop] [Done, Go Back] [Close Controller, Go Back - 06] Turn ignition off The LED in the parking brake switch and the warning lamp in the instrument cluster will probably continue to blink rapidly in addition to Fault code C1011 - Brake pad replacement mode active. This should stop after cycling the Parking Brake ON, then OFF again using the switch in the vehicle while holding the brake pedal AFTER all rear brake components are reassembled.

Audi Q3 (8U/FS)

Ältere Fahrzeuge nutzen die STG53, neuere Fahrzeuge erfordern die VW_Golf_VII_(5G/AU)_ABS_Bremselektronik Prozedur.

A4/S4/RS4/Cabriolet (8K)

A4/S4/RS4/ (8W)

A5/S5 (8T)

Audi Q5 (8R)

A6/S6/RS6/Allroad (4F/FB)

A6 (4G/4H) / A7 (4G)

A6/S6 (4K)

A8/S8 (4E)

A8/S8 (4H) (4H Fahrzeuge nutzen die Audi A6 (4G/4H) EPB Prozedur)

Bentley

Continental (3W)

VW

Passat (3C/AN) Passat Coupe (35) Tiguan (5N/AX) VW Touareg (7P) VW Golf VII (5G/AU) (Rest of World MQB platform ABS)